|Place of Origin:||
Guangdong China (Mainland)
* Nema23 Stepper Motor, Driver, Interface Board & Power Supply Kit;
* 4pcs 175Oz-in & 2.8A motors;
* USB Breakout Board.
4 Axis CNC Nema23 Stepper Motor, Driver, USB Interface Breakout Board, Power Supply Kit
1. Nema 23 Stepper motor
Step Angle Accuracy: +-5%(full step, no load)
Resistance Accuracy: +-10%- Inductance Accuracy: +-20%
Temperature Rise: 80 Degrees Celsius CMax.(ratod current,2 phase on)- Ambient Temperature: -10°C-+50°C
Insulation Class: B
Dielectric Strength: 500V AC for one minute
Shaft Radial Play: 0.06Max.(450g-load)
Shaft Axial Play: 0.08Max.(450 9-load)
2. Motor Driver
HY-DIV168N-3.5A subdivision-type two-phase hybrid stepping motor drive using DC 12 ~ 36V power supply, suitable for drive
Two-phase hybrid stepping motor dynamic voltage 12 to 36V, the current is less than 3.5A outer diameter of 35 to 86 mm.
This drive using the drive's current loop subdivision control, the motor torque ripple is very small, low-speed running is very smooth, almost no vibration and noise.
High-speed torque is much higher than other two-phase drive, high positioning accuracy. Widely used in the engraving machine, CNC machine tools, packaging machinery and other high resolution requirements on the device.
average current control, two-phase sinusoidal current drive output
DC 12 ~ 36V power supply, the internal integration of 12V and 5V regulator
optically isolated signal input / output
overvoltage, undervoltage, overcurrent, and white short-circuit protection
4 file segmentation and automatic half-streaming capabilities up to 16 segments
file output phase current settings
high starting speed
Input voltage DC 12 ~ 36V input
The input current of 1 to 4 amps, select the drive a stepper motor.
Output current of 0.5A ~ 3.5A
Temperature Operating Temperature -10 to 45 °C; Storage temperature -40 °C to 70 °C
Humidity not condensing, not drops
Gas prohibit combustible gas and conductive dust
1). the definition of control signals:
PUL +: step pulse signal is input side or the positive pulse signal input positive terminal
PUL-: the negative input of the negative input pulse signal or a positive pulse signal
DIR +: stepping direction signal input to the positive terminal or negative pulse signal input to the positive terminal
DIR -: stepping direction signal input of the negative side or reverse step pulse signal input negative terminal
EN +: offline can reset signal input side is
EN-: offline can reset signal input negative terminal
Offline enable signal is active, reset drive failure to prohibit any pulse, the output of the drive
Power component is turned off, the motor holding torque.
2).Control signal connections:
PC control signal can be high, also can be low effective. When active high, the control signal
The negative side together as a signal to active low, positive side of all control signals together as a signal common.
3. USB Interface Breakout Board
1) The maximum matching 5-axis stepper motor driver
2) The two-stage signal processing, signal transmission smooth, powerful anti-jamming
3) 5 input interface to define the emergency stop, limit, points in the knife, etc.
4) relay output control interface, can be accessed by the spindle motor or the air pump, water pump, etc
5) five-axis job LED display, visual display products, working condition
Input Power:5V DC power supply or computer USB to take power
Work axis stepper:Received the highest 5-axis independent driving
Drive:Pulse + direction + enable signal
(Reference manual provided on the software CD)
4. Power Supply
What is in box ?
4 x Stepper Motor 57BYGH56-401A
4 x 3.5A stepper motor driver
1 x USB CNC breakout board
1 x 250W 24V 10A power supply
1 x Parallel Port Cable
|Items per Carton:||1 Sets/Carton|
|Package Measurements:||35X30X30 cm|
|Gross Weight:||6.5 kg|
|Package Type:||Carton Box with Foam Protection|