|Place of Origin:||Zhejiang China (Mainland)||Brand Name:||Mikehome||Model Number:||JN7-56|
|Packaging Detail:||1 pcs in a carton|
|Delivery Detail:||within 15 days|
1. suitable for the families and specialized households
2. incubate chickens, ducks and geese, etc
I. Operating Steps:
1. Open the box and check the incubator, check whether all of the accessories inside of the packing box are well-equipped.
2.Before use, remove the top cover on the incubator, there are movable egg tray bracket and egg tray mesh inside the base. In order to prevent damage during the transportation, the base, movable egg tray bracket and egg tray mesh are tied up during package, please disassemble it before use.
3.Take movable egg tray bracket and egg tray mesh out of the base. Wash and clean the base, feed water to tank A and B inside of base, then put the movable egg tray bracket into the base.
4.After covering the top cover, rightly connect the power line and switch on the power supply, if temperature is indicated on the control panel in normal condition, the heating indicator (Work) will be on incubator will begin to heat up.
5.Note: when ambient temperature is less than 25°C, measure shall be taken for heat preservation, it’s good for temperature uniformity when the device is enclosed with clothes or other warms, and it also helps energy-saving and reduces heat dissipation.
6.Check all parameters according to Push-button Instruction.
7.Turn over the movable egg tray bracket at least twice one day.
8.The incubator can be put into running after 2 hours’ trial.
9.It’s about to incubate, put the selected eggs well and the bigger side shall be up, take down the incubation time.
10.The incubator begins to incubate, pay attention to the temperature indicated on the control panel, adjust it in time if it doesn’t comply with requirement, check the water level for every 2-3 days so as to avoid incubator in lack of water.
11. After incubation for 18-19 days (take egg as example), the egg tray shall be exchanged, firstly, take the egg off from movable egg tray bracket, and take egg tray out of the incubator, put the egg tray mesh into the incubator, and lay one layer of egg on the egg tray mesh, then wait for the young poult to break the shell and come out.
12.The egg tray exchange time is different according to number of incubation days of kinds of poultry, it usually takes 3-4 days less than the number of incubation days. It’s also the time to exchange the egg tray when one or two eggs breaks.
12.Pay attention to temperature and relative humidity adjustment during the whole incubation process, refer to Incubation Technology in the operation instruction for more details.
II. Important for Safety
1. Only the power supply marked on the incubator can be used, 220-240v;
2.Don’t put any goods on the wire, the power line of incubator shall be placed where it won’t be stepped on or make people trip and fall;
3.Make sure that the socket and extension line in use don’t overload, otherwise, it may cause fire or electric shock;
4.If the incubator is smoking, or sending abnormal smell or unusual noise, please cut off the power supply and pull down the power line to stop the fault, after that, contact the agency or maintenance center;
5. Don’t touch the power line with wet hand, or it may cause electric shock;
6. This incubator can’t be exposed to rain and sunshine;
7. Make sure that the power supply is switched off before cleaning the incubator;
8.The incubator shall be placed in room where has good air but no vibratory equipment, it can’t be placed in room with fast
air movement or room with harmful and noxious chemicals and other pollutants.
9. Don’t block the air-bleed hole when the incubator is in work condition.
A: Push SET once to enter temperature control set, push <+> or <-> to adjust parameter, push<+>or <-> for 3s to enter fast adjustment mode, push SET again to exit from setting state.
B: Push SET for 3s to enter system menu set, push <+> or <-> to select menu in need of adjustment, then push SET again to enter relative parameter setting state, push <+> or <-> to select parameter in need of modification, push RST to exit after adjustment, or the system will exits after 5s delay.
3.<->: Down button
Indicating lamp state instruction:
WORK lamp on the left side of display screen is made as work indicating lamp, LED normally on means it’s in heating state.
SET lamp on the left side of display screen is used for indicating lamp set, LED normally on means it’s in setting state.
Pls inform me to send more infomation. Waiting for your inquiry.