High Performance Polyurea Urethane Primer

FOB Reference Price:Get Latest Price
100 Kilogram/Kilograms (Min. Order)
Supply Ability:
10000 Kiloampere/Kiloamperes per Week
Shenzhen China
Report Suspicious Activity
Quick Details
CAS No.:
Other Names:
Place of Origin:
China (Mainland)
Main Raw Material:
Boat Paint, Building Coating, Car Paint, Furniture Paint, Plastic Coating, Road Marking Paint, Rubber Coating
Application Method:
Liquid Coating
Brand Name:
Model Number:
FY 2930
other color
Packaging & Delivery
Packaging Details
20kg/drum or 200kg/drum
Delivery Time
10 days


High Performance Polyurea Urethane Primer

High Performance Polyurea Urethane Primer



A high performance, two component primer for use where rust inhibition, chemical and corrosion resistance are paramount. For use on automobiles, trucks, trailers, railway cars, service stations, bulk tanks or chemical (acid or caustic) trailers. For best results, use one of the FY 2930 engineered systems for a total coating system.


• Solvent resistant

• Chemical resistant

 • Primer/Surfacer

• Lead and Chromate free

 • Low VOC - 100 g/L



Colors                                         White

Gloss......................................... Low Gloss

VOC (mixed)............................. 100 g/L (0.83 lbs/gal)

Weight/Gallon (mixed)............... 13.45 pounds

Solids by Weight (mixed)........... 78.6%

Solids by Volume (mixed).......... 65.8% (

Theoretical) Viscosity (base)......................... 15" / Zahn 3

Flash Point (white).................... 40oF

Dry Heat Resistance................. 300oF (149oC)

Freight Classification................. See MSDS

Packaging................................. 1 Gallon (mixed unit)





URED FILM PFORMANCE Description Test Method Results Adhesion to Steel ASTM D4541 >500 psi Hardness ASTM D3363 H Impact Resistance ASTM D2794 60 Direct Corrosion Resistance ASTM B117 No Under Cutting 500 hrs. Salt Fog


EQUIPMENT RECOMMENDATIONS Listed below are general equipment guidelines for the application of this product. Job site conditions may require modifications to these guidelines to achieve the desired results.



Fluid Tip Fluid Delivery Atomizing

Pressure Pressure 63 pb 66 oz/min 45 - 60 psi

Pressure DeVilbiss 704 fx oz/min 45 - 60 psi

AIRLESS SPRAY: Model Pump Ratio Fluid Tip Fluid Pressure Filter

Mesh Bulldog 30:1 .011 - .013 1800 - 20 100 B 8D 35:1 .011 - .013 1800 - 20 100


GENAL SURFACE PREPARATION All surfaces must be sound, dry, clean and free of oil, dirt, grease, wax, mildew, loose or flaking paint and other surface contaminants. Remove loose, peeling, flaking or scaling paint and rust by scraping, sanding or wire brush or blasting. For best results, an SSPC-SP 5 white metal blast is minimum for severe exposure. For moderately severe (non-immersion) exposures an SSPC-SP 6 ) commercial blast can be used.


DIRECTIONS FOR USE TINTING: Not recommended. THINNING: See Application Data.. Note: Always know local VOC restrictions for coating applications in your area before thinning this product. Thinning recommendations meet VOC restrictions for architectural coatings. This product and other referenced products may not meet VOC restrictions for your application and may not be available in your area. Carefully read and observe warning on thinner labels. HS-4 High Performance Polyurea Urethane Primer Technical Data APPLICATION: Mix thoroughly before use. Add 1 quart of HS-110 or HS-111 per ¾ gallon unit of HS-4 then mix thoroughly again. Only apply when air and surface temperature are between 40o – 100oF (7o - 38oC) and when the surface temperature is at least 5oF or 3oC above the dew point. DRYING TIME: See Application Data for typical dry times. Low temperature, poor ventilation and thick films will retard drying. HJ1104 may be added at the rate of up to 0.5 fl oz per mixed gallon of HS-4 to reduce the drying time.


CLEAN UP: Clean up paint tools or spills immediately with recommended thinner, carefully observing cautions on paint and thinner labels. Dried paint may be removed by scraping.


ENGINEED SYSTEMS SYSTEM - A For maximum corrosion resistance and durability. Recommended for use in coastal and marine exposures above the splash zone over a sandblasted surface. First coat Primer: 3 dry mils of Organic Zinc Rich Primer. Second intermediate coat: 3-5 dry mils of HS-4. Topcoat: 3 dry mils of Itin the desired color for the finish coat. Clearcoat: 1 dry mil of ItClear (optional for ultimate gloss and durability). SYSTEM - B For maximum chemical resistance while affording excellent corrosion resistance and durability in non-salt atmospheres. Recommended for use in inland areas and for resistance to acid and alkali. Sandblasting is recommended. First coat Primer: 3 dry mils of HS-4. Topcoat: 3 dry mils of Itin the desired color for the finish coat. Clearcoat: 1 dry mil of ItClear (optional for ultimate gloss and durability). SYSTEM - C Recommended for refurbishing existing equipment and struc structures that have a surface suitable for refinishing by sanding and spot cleanup with hand and power tools. First coat Primer: 2 dry mils of HS-4. Topcoat: 2 dry mils of Itin the desired color for the finish coat. Clearcoat: 1 dry mil of ItClear (optional for ultimate gloss and durability). ALTNATE PRIMS: .


HEALTH AND SAFETY Read the Material Safety Data Sheet (MSDS) and container labels for detailed health and safety information. This product is intended for industrial use by properly trained professional applicators only. The information, data and suggestions contained herein are believed to be reliable, based upon our knowledge and experience; however, it is expressly declared that Seller does not guarantee the result to be obtained in Buyer’s process.