Maydos JD-2000 is a kind of two-pack self leveling weathering&corrosion resistant floor paint. It owns such features as weathering resistance, corrosion and yellowing resistance which make it suitable for indoor or outdoor use. It can combine with the concrete substrate tightly. Low shrinkage, wearable and durable. JD-D10 is a two-component solvent epoxy primer. It has good penetration and sealing power on the porous substrate, such as concrete and water whetstone, etc. It can reinforce the substrate strength and provide good adhesion. It is also an all-purpose primer for epoxy series paints and used as the undercoat or putty coat after used together with quartz sand or quartz powder.
Advantages: 1. Beautiful, seamless, dustproof and easy to clean. 2. Strong adhesion, small shrinkage 3. Corrosion-resistance to the general chemicals. 4. Good abrasion resistance and durability.
Configuration of Coating System: Requirements for the base: 1. Concrete strength≥C25; 2. Flatness: the maximum altitude difference of 2M running rule<3mm. 3. The moisture content of the base<4%
Technical Data: Drying time: Touch dry: 4 hours Hard dry: 2-4 days Compressive strength (Mpa): 80 Impact resistance strength (Kg·cm): 40 Flexural strength (Mpa): 40 Adhesive force grade: 1 Pencil hardness (H): 3 Abrasion resistance(750g/1000r, zero gravity, g)≤0.03 Service life: 8-10 years Recommended Consumption: Primer: 0.15kg/sqm Undercoat: 0.3kg/sqm Putty layer: 0.2kg/sqm Quartz Sand: 0.45kg/square meter Quartz Powder: 0.2kg/square meter Top coat: 0.8kg/sqm
Application instructions: 1. Surface preparation:Correct substrate preparation is critical for optimum performance. Surfaceshould be sound, clean, dry and free from loose particles, oil, grease, and other contaminants. 2. Primer: Mix JD-D10 A and JD-D10B in a barrel according to 1:1 by weight. The referenceconsumption is 0.15kg/sqm.The main purpose of this primer is to seal the substrate completely andavoid air-bubbles in the body coat. According to the oil absorption condition of substrate, a secondcoat may be required. The paint should be stirred evenly, then apply directly with roller. Wait for 8hours to recoat.Inspection standard for the primer: even film with certain brightness. 3. Undercoat: Prepare a barrel, mix JD-D10A and JD-D10B according to 1:1 in it, pour in appropriatequartz sand, stir completely and then apply the mixture with trowel. Wait for about 8 hours, sandthe coat with grinding machine, clean the dust and then continue the next process.Inspection standard for the undercoat: Non-sticky to hand, no softening, no nail print if youscratch the surface. 4. Putty layer: Prepare a barrel, mix JD-D10A and JD-D10B in it according to 1:1, pour in appropriatequartz powder, stir completely and then apply the mixture directly with trowel. Wait for 12 hours,sand the coat with grinding machine, clean the dust and continue the next process.Inspection standard for the putty layer: Non-sticky to hand, no softening, no nail print if youscratch the surface. 5. Top coat: Mix JD-2000A and JD-2000B according to 5:1 and then apply the mixture with scraper. 6. Overcoat varnish: Apply this varnish over the top coat with roller. The consumption quantity is0.1kg/sqm. One coat will be enough. 7. Maintenance: 5-7 days. Don’t use or wash with water or other chemicals.
Clean up Clean tools and equipments first with paper towels, then clean the tools with solvent before the painthardensHealth and safety informationIt contains certain chemicals which can cause skin irritation. Wear gloves, masks while handling theproduct, washing thoroughly after handling. Should skin contact occur, wash immediately with soapand water.During application and curing in closed rooms, adequate fresh air ventilation must be provided. Keepaway from open flames including welding.In case of accidental eye contact, wash with a large quantity of water and immediately seek medicaladvice.For detailed health, safety, environment recommendations, please consult and follow the instructionon the product material safety data sheet.
Disclaimer The information given in this sheet is not intended to be exhaustive. Any person using the productwithout first making further written enquiries as to the suitability for the intended purpose does so athis own risk and we can accept no liability of the product for any loss or damage arising out of suchuse. Product data are subject to change without notice and become void five years from the date ofissue.
Note The above information is given to the best of our knowledge based on laboratory tests and practicalexperience. However, since we cannot anticipate or control many conditions under which our productsmay be used, we can only guarantee the quality of the product itself.We reserve the right to alter the given information without prior notice.
Packaging & Shipping
5L(6.5KG), 2 tins in 1 carton, 1620 tins for one 20FT container
18L(22KG), no carton package, 1078 tins for one 20FT container 20L(24KG), no carton package, 924 tins for one 20FT container
Packaging & Shipping
1.How can you prove that you are a paint manufacturer rather than a trading company? As the one of The Top 5 paint manufacturer in China.
We have many years of experience since 1996 in production and export,welcome to visit our factory at any time. 2.How about the price ? We can offer the best wholesale price which depend on the quantity of the order. 3.I need to make sure the quality and the color . Our pleasure!We can offer the liquid Free sample for you to test and color chart. 4.If the paint is not ideal, what can I do? We have perfect after-sales service to help to complete the construction smoothly. Even if there are any unexpected things in your order, we will assist to solve them. 5.What's your MOQ (min order quantity),production period and delivery time? Our MOQ is 200Kg. We accept mixed order and the production period and delivery time are 7-10 days. 6.I want to put my Logo on the packing . We can accept the OEM, waiting for your details requirement.