Automatic Melting Furnace Operating Process as follows
Step 1 Put gold bar into the crucible.
Step2 Heat up the furnace with 15 minutes
Step3. Take out the Melting crucible from the furnace,then put it on tray.
Step4.Pour slowly the gold liquid from the crucible.
Step 5.Wait the liquid cooling in the mould within several seconds.
Automatic Melting Furnace Technical Data:
0C--1200C about 15-25 mins
Adopting AI PID control method; Measured values (PV), set data (SV) can be shown at the same time; Set data can be changed by arrow buttons
Material of the furnace liner
Ceramic fiber insulation materials
Material of the furnace cover
With thermocouple input, relay output
Automatic Melting FurnaceInstruction
The furnace has two on/off switches: the GREEN switch turns on the temperature thermostat allowing you to set the desired melting temperature.
The RED switch turns on the heating element to start the melting process.
The thermostat has two digital read-outs: the bottom readout (SV) displays the setting you enter into the furnace. The top read-out (PV) displays the actual temperature inside the crucible during operation.
To set the desired melting temperature, turn on green on/off switch. Wait a few seconds; the bottom (SV) readout should show the default temperature setting of 1950°F.
To change the temperature setting, simply press the left arrow key to move the cursor to the proper desired digit and press the up or down keys to adjust it up or down. Adjust each digit to the desired setting.
When you are ready, place the metal pieces or grain in the crucible and set the crucible in the furnace. Close the lid.
Press the red button to start the melting process.
When the metal is molten and has reached casting temperature, turn off the red switch. Open the lid and pour the metal into your prepared flask.
Difference Feature JIUCHEN with Other Similar Furnace
JC Electric Furnace
Other Similar Furnace
Adopts new advanced SIC material with no crack no distortion under normal temp 1-1200 Degrees Celsius,which prevents disadvantage of short work life with tranditional ceramic fiber, quartz chambers.
Traditional chamber material:ceramic fiber, quartz with easy crack and distort after use 2-3 times,which easily lead to short circuit and reduce work life.
Material: Fe-Cr-Ni alloys Limited test temp up to 1600°C,make sure long continues continuous work time under normal 1200°C,which effectly extend furnace work life
Easy to crack after use 2-3times and lead to be out of work,it is very complicated process if replace coil singly,also many end users unable to replace it successfully by themselves.
JC-K-110-2(110V 2Kw) 15-20Mins
Then need 10-15mins to complete finish the melting.
1-1200 Degrees Celsius
1-1150 Degrees Celsius
Automatic Melting FurnacePackage
Automatic Melting Furnace Shipping
We can accept T/T,Paypal,Western Union,Escrow,the best and fast way is Paypal.
We choose DHL/Fedex/UPS usually takes about 3-5 working days to the destination,
We will send the goods within 3 working days after the full payment has been confirmed.
Warranty and Return:
All the products have been tested before ship out.
All products electrical parts have 1 year warranty,including temperature controller,relay, thermocouple,heating elements have 6 months warranty,including chamber,heating coil etc.
If there is no man-made problems,we will replace or repair for you freely.
Founded in 1998, Zibo Jiuchen Industry &Trade Co.,Ltd.locate in Zibo city , Shandong Province, the Ceramics capital of China.
The factory have 6 product lines with a annual capacity of 6000 ton ceramic fiber bulk ,10000ton Ceramic fiber board,12000 ton Ceramic fiber blanket etc.Our main products covers kinds of ceramic fibers,such as ceramic fiber bulk, ceramic fiber board, ceramic fiber blanket ,ceramic fiber felt,ceramic fiber textiles, ceramic fiber paper, ceramic fiber module and other ... View detail