You thought it couldn't get better than our world-famous 60/64-LED-per-meter Digital LED strip but we will prove you wrong! You wanted twice the LEDs? We got it (well, its 1.875 times as many but that's within a margin of error). You wanted thinner strips? Now only 12.5 mm wide, 10 mm if you remove the strip from the casing. You wanted less noticeable strip color - this strip has white-colored flex PCB, which will be less visible against white-painted walls. This is the strip with white flex PCB, its identical to the black 60/64 LED/meter except it has a different color mask on the flex strip, Black PCB is available.
First up, the higher density means much higher power usage over a certain distance - 18 Watts max (~3.5 Amps @ 5V) per meter instead of 9.6 Watts max (~2 Amps @ 5V). The max rating is assuming all the LEDs are on full white, usually the actual current for colorful design is about 1/3 to 1/2 the max current. A good power supply such as our 5V 10A supply is key!
Second, to get high density, the controller chip is inside the LED, which is kind of cool, but also means that the chip only uses a single pin for input and a single pin for output. The protocol used is very very timing-specific and can only be controlled by microcontrollers with highly repeatable 100nS timing precision. We have example code for using with the Arduino Uno/Mega microcontroller at 8MHz and 16MHz, but it will not work with the Raspberry Pi, Basic Stamp, NETduino, any other interpreted/virtual machine microprocessor or any processor slower than 8 MHz. For those processors, check our 32 LED/meter digital LED strip which has SPI-like input/output and works well with Pi, NETduino, and other processors.
Third, just because you have all those pixels doesn't mean you have the RAM for it - the entire strip must be buffered in memory, and we've found many Arduino UNO projects only have about 1500 bytes of RAM available after all the extras are included - enough for about 500 LED pixels. If you want to drive the entire strip and have some other libraries included, use a Mega.
These LED strips are even more fun and glowy. There are 60 RGB LEDs per meter, and you can control each LED individually! Yes, that's right, this is the digitally-addressable type of LED strip. You can set the color of each LED's red, green and blue component with 8-bit PWM precision (so 24-bit color per pixel). The LEDs are controlled by shift-registers that are chained up down the strip so you can shorten or lengthen the strip. Only 1 digital output pin are required to send data down. The PWM is built into each LED-chip so once you set the color you can stop talking to the strip and it will continue to PWM all the LEDs for you
The strip is made of flexible PCB material, and comes with a weatherproof sheathing.
You can cut this stuff pretty easily with wire cutters, there are cut-lines every 1 LED each.
Solder to the copper pads and you're good to go. Of course, you can also connect strips together to make them longer, just watch how much current you need!
We have 5V/40A supply that should be able to drive 5 meter (depending on use) and a 5V/4A supply that can drive up to 1 meters (depending on use).
You must use a 5V DC power supply to power these strips, do not use higher than 6V or you can destroy the entire strip
They come in 4 meter reels with a 2 or 3-pin JST SM connector on each end and separated power/ground wires. These strips are sold by the meter! If you buy 4 meters at a time, you'll get full reels with two connectors. If you buy less than 4m, you'll get a single strip, but it will be a cut piece from a reel which may or may not have a connector on it.
To wire up these strips we suggest picking up some JST SM plug and receptacle cables. You'll want one of each, one wire is for ground the other is for signal. For the power wire, you will also probably want a 2.1mm DC jack to wire in so you can connect one of our wall adapters to power it.
QTY of LED: .60leds/meter, 300leds/roll, each LED addressable;
Pitch: 16.6 mm; smd 5050 ws2812 strip DC5V 60LED
Color scale: 256;
Bits/color:8-bits/color; 24bit for a RGB LED
Controller: CL-1000s Controller(can control 32meters), DMX512 or CL-300k;
FPC color:white, black are available;
Protection rate: Both waterproof (IP65, IP67,IP68) and non- waterproof(IP40) are available;
Colors: Full color RGB, dream color changing; 256*256*256
Cuttable:each LED can be cut off.
Packaging & Shipping
1. Payment term: Western Union & T/T, and Paypal for samples;
2. Lead Time: 3~7 days (5~800 meters); 10~15 days(800~1000meters);
3. Sample can be delivered in 3 days;
4. .Shipping method: At your request;
5. Shipping port: Shenzhen, Mainland China;
6. Discounts are offered based on the quantities;
7. Minimum: 5 meters.
8.led light swimming pool rope light
1. All kinds of latest LED products can be provided with high quality based on reasonable profit;
2. We mainly produce Pixel LED module, LED strip lights (especially digital smart strip lights), high power LED lights, LED panel light, LED tube lights, DMX LED flood lights, etc;
We can design and produce at your special request for rgb led strip rolls ws2811 ic , such as Different type of IC: ws2801, ws2811, LPD8806/6803, TLS3001, TM1809/1803/1804/1812, HL1606,etc. Rigid or flexible strip are allowed. Different LED source: 5050, 3528, 2835, 5630, 0805, 3014,etc.
3. Technical assistance
4. Good after-sales services
LED point Light, LED Pixel Module, LED Light Strng.
Shenzhen Clen Optoelectronics Co., Ltd., which is located at Shiyan Town, Bao"an District, Shenzhen City, Guangdong Province, China, is a professional manufacturer engaged in developing, manufacturing and marketing lighting products. Clen specializes in producing pink, red, yellow, orange, green, cyan, blue, purple and white LED. The wavelength range is from 375nm to 700nm and within this range any wavelength and shape is available. With Special technology and technique, Clen white LED series ... View detail