3 Axis 6.5Nm NEMA 34 Stepper Motor 2 Phase Stepper Drive 400W 60V DC Power Supply 5Axis Breakout Board Kit for CNC Router Lathe
Note : If you need the dual shaft stepper motor , please leave us messages . Otherwise, we will ship the default single shaft stepper motor .
Package Included :
3 x MA860H Sumtor step motor drive 2ph 24~110VDC AC18-80V 2~7.8A
3 x 86BYG 2ph Hybrid stepper motor 86HS9860A4 L 98mm 4-lead 6A 6.5NM 1.8 degree
3 x Switching Power Supply 400W 60V 6.7A for CNC S-400-60
1 x 5 Axis CNC Breakout Board Interface For Stepper Motor Driver (free offer)
1 x DB25 Parallel Cable & USB Power Cable (free offer)
Stepper motor : 86HS9860A4
Shaft length: 37mm
Shaft Type: double-sided milling flat 1mm
Shaft diameter: 14mm .If you need keyway shaft, please write us to ship keyway shaft after order. The same price.
is customized : yes
holding torque: 6.5nm
brand name: sumtor
current : 6A
certification: CCC,CE, ISO
step angle: 1.8degree
Step Angle (º)
Rated Current (A)
Phase Resistance (ohm)
Phase Inductance (mH)
Holding Torque (N*m)
Detent Torque (N*cm)
Rotor Inertia (g*cm2)
Motor Length (mm)
Motor Wire (No.)
Motor Weight (kg)
Electrical Properties (ambient temperature Tj = 25C pm):
Logic Signal Current
Pulse Input Frequency
Connector P1 Configurations:
Pulse signal: In single pulse (pulse/direction) mode, this input represents pulse signal; 4-5V when PUL-HIGH, 0-0.5V when PUL-LOW. In double pulse mode(pulse/pulse) , this input represents clockwise (CW) pulse,active at high level or low level (set by inside jumper J1 & J2). For reliable response, pulse width should be longer than 1.5μs. Series connect resistors for current-limiting when+12V or +24V used. The same as DIR and ENA signals.
DIR signal: In single-pulse mode, this signal has low/high voltage levels,representing two directions of motor rotation; in double-pulse mode (set by inside jumper J1 & J2), this signal is counter-clock (CCW) puls. For reliable motion response, DIR signal should be ahead of PUL signal by 5μs at least. 4-5V when DIR-HIGH,0-0.5V when DIR-LOW. Please note that motion direction is also related tomotor-driver wiring match. Exchanging the connection of ?two wires for a coilto the driver will reverse motion direction.
Enable signal: This signal is used for enabling/disabling the driver. High level(NPN control signal, PNP and Differential control signals are on the contrary,namely Low level for enabling.) for enabling the driver and low level fordisabling the driver. Usually left UNCONNECTED (ENABLED)
Connector P2 Configurations:
Power supply, 18~80 VDC or 24~110VDC, Including voltage fluctuation and EMF voltage.
Motor Phase A
Motor Phase B
Input voltage: AC110-230V (supports 110V has a pull switch)
Output voltage: DC60V 6.7A
Output Power: 400W
Size: 215 * 115 * 50MM
5 axis CNC Breakout Board:
High performance, cost-effective.
Maximum support 5-axis stepper motor driver controllers.
Compatible with MACH3, Linux CNC (EMC2) etc. parallel-control CNC software.
USB power supply and peripherals powered phase are separated to protect computer security.
All the signals are opto-isolated which can protect your computer security.
5-input interface to define the Limit, Emergence-Stop, Cutter alignment etc.
Wide input voltage range: 12-24V, and with anti-reverse function.
One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
Output 0-10V analog voltage for inverter to control the spindle speed.
Electrical properties (ambient temperature Tj = 25C pm):
USB port from PC or 12-24V power supply(optional)
Pulse and Direction Signal Control
Suitable Microstep Driver
2 Phase Microstep Driver
90 * 70 * 20mm (L*W*H)
Fast To Buy Limited, founded in 2011, provide CNC parts, CNC kits and CNC solutions for the CNC users and the manufacturers over the world. Our customers are getting more and more, until now, there are more than 40000 customers who are from United States, Russia, United Kingdom, Canada, Germany, Australia, France, Spain, Mexico, Brazil, Italy, etc.
The parts for CNC include:
CNC Control System, Servo System, Stepper System, Reducer, VFD, PLC,Spindle, Guide Rail, Electric Control Panel,CNC Tools, CNC Machine Accessories and Motors.
Different kinds of CNC Routers
such as: Woodworking CNC Router, Laser CNC Router, Metal CNC Router and Plasma CNC Router
such as: Wood Engraving, Metal Cutting, Abrasive Printing, Outdoor Welding, Mining Mining, Plastic Processing, 3D Printing, Medical Equipment, Municipal Services, Automotive, Rail Transit.
Some parts for CNC are the famous brands, such as Yaskawa, Mitsubishi, Siemens, Panasonic, Samsung etc.
At the same time, we provide many CNC Parts with good quality and good price for our customers who are the users, manufactures of CNC Routers and CNC Machines.
If you are the users of CNC (such as CNC Router):
These parts are high quality and not so expensive, anymore, you can buy the parts on our online shop from one piece. And we have quick and flexible shipment to let you get it as soon as possible (about 7days).
The users of the woodworking, metal process, plastic process can buy the good parts for their CNC including the CNC Routers for building and upgrade. Above all, we also have the service to help the users to get special parts they need and provide them the Technical solutions .
If you are the manufactures of CNC Routers:
Our OEM Department with Professional technical service engineers, sales engineers and professional services provide you parts & kits and OEM service according your CNC Routers. Our aim is to reduce the cost so that your Routers will have Competitiveness in the market.