Vacuum level: below 0-08PA Working pressure:8-10PA
Transparent glass capacity: 1OL
Oil storage tank: 80L
Media: machine oil and gear lubricant
The greatest pressure:4KG/cm
Diameter 6.5mm collecting speed:1.6L/min
III Operation instructions
1. Pump waste oil to oil tank:
a Connect a well-selected oil drain pipe and oil exhaust pipe and then insert them in the sight oil hole of the engine with lubricant, next switch off the oil exhaust pipe;
b Turn on the switch of transparent glass connected to oil storage tank, switch off the elbow to prevent discharge of oil, switch off the quick coupler on the top of the tank and under the oil funnel;
c Connect the quick coupler on the top of oil measuring glass to compressed air tube and switch on, while the indication of the vacuum gauge will decrease;
d when the vacuum pressure lowers below 0.5 PA, switch on the oil exhaust pipe and thus the waste oil will be pumped out of the engine and flows to the tank quickly via the oil exhaust pipe.
2. Pump waste oil to transparent glass
a Connect a well-selected oil drain pipe and oil exhaust pipe and then insert them in transparent glass of the engine with lubricant, next switch off the oil exhaust pipe;
b Turn off the switch of transparent glass connected to oil storage tank;
c Connect the quick coupler on the top of transparent glass to compressed air tube and switch on the compressed air tube, while the indication of the vacuum gauge M/ill decrease;
d when the vacuum pressure lowers below 0.5 PA around: switch on the oil exhaust pipe and thus the waste oil will be pumped out of the engine and flows to the tank quickly via transparent glass .
3. Flow waste oil to the oil storage tank from transparent glass
Turn on the switch of transparent glass connected to oil storage tank, thus waste oil will be discharged to the oil storage tank from transparent glass .
4. Flow waste oil out of the oil storage tank
a Turn off the switch of transparent glass connected to oil storage tank (notice: If it turns on excessive air pressure may damage transparent glass and even persons; we will assume no responsibility for man-made injuries due to improper operation.); and switch off the ball valve.
b switch on the elbow that hooks the tank.
c Connect the quick coupler on the top of the tank to compressed air tube and switch on the compressed air tube, thus waste oil will be discharged via the elbow (notice: it may switch off the compressed air tube when the safety valve begins to exhaust.)
Notice: Air inflation must be available while pumping oil, by doing so it is to reduce gas consumption and pressure to realize faster pumping.
1. Solutions for non-reduction of pressure of the vacuum meter
a Check to confirm the air pressure is 8-10PA.
b Check to confirm all valves that should be turned off are in proper condition.
c Check to confirm sound sealing of transparent glass and oil storage tank.
2. Solutions when pressure of the vacuum gauge reduces, yet it fails to suck oil
a Check to confirm sound sealing of the oil drain pipe and oil exhaust pipe;
b Check to confirm whether the temperature of the waste oil is too low;
c Check to confirm whether the oil pipes are switched on;
d Check to confirm whether the oil pipes are stopped or contact the bottom of the tank.
V Tips for maintenance
Clean this machine to make sure it is without faults for many years
a Check the machine is with leakage or not regularly; if there is leakage, please repair after examination immediately;
b Check the tube is connected c1osely frequently;
c Do not keep the waste oil in bucket for1ong time to avoid corrosion to the bucket;
d Wipe the surface of the machine by using towe1 or cloth; keep the machine clean and place it in shadow to avoid direct sunshine.
a Personnel qualified after training can only use this machine;
b No smoking in surrounding of the machine;
c This machine can better operate under60-80°C, then the thickness of the machine oil is as1.3 times as water, and speed lower than water. In case of below such temperature, it may cause unsmooth pumping and fai1 to pump oi1;
d This machine should be provided with an air compressor with10PA output pressure. It is8PA at the machine nozzle. If it is less than that, the vacuum level is insufficient, which may cause unsmooth pumping and fail to pump oil;
e When the two points above are met, it should use big-inch oil drain pipe to pump oil. An iron tube is featured by directf1owing; a big iron tube can reach1.8L/min, and a sma11 one1.4L/min. while, a plastic tube may bend; a big plastic tube can reach- 1.8L/min, medium-sized 06 L/min. and a small one 0.4L/min. the oil drain pipe cannot be inserted too deeply, or else it is impossible to suck oil;
f When the oil exhaust pipe is used for long time, it may leak. If so, check the quick coupler on the top of the pipe to determine it is loose or not(This can be done as fol1ows: insert one sealed end of the pipe in oil, blow to the other end of the pipe to check whether it leaks. If it does, repair or exchange the pipe);
g For Toyota Camry, the dipstick is above the machine, the oil drain pipe cannot be inserted in it sometimes, and even if it is inserted, it cannot pump oi1 or turn off. To overcome that, it is suggested to discharge oi1 with a screw;
h There is a muffle on the top of transparent glass. When the air compressor is fi11ed with water or operated improperly, oil or water willf1ow.After solve that problem, there will be no waterf1owing out.
Packaging & Shipping
Within 30 days after confirmed the purchase order
G.W./N.W.:19/18KG Carton Size:51.5*40.5*81CM
Q1: What Certificates do you have? A: We have CE Certification.
Q2: What is your sample policy? A: Usually, we send sample by express freight collect.
Q3: How many days for the mass producing? A: It take 25 days after we confirm all artwork.
Q4: What payment terms do you do? A: T/T.
Q5: What’s your MOQ? A: Our MOQ is 50pcs.
Q6: Can you do OEM? A: Yes, our factory can offer OEM according to your requirements.
Q7: How long is your delivery time? A: Generally is 5~10days if the goods are in stock, or it’s 25 days if the goods are lack of stock, and it’s based on the quantity.
Q8: Do you provide samples? Is it free or extra? A: We can provide sample, the sample price difference can be returned when formal order.
Q9: What’s your terms of payment? A: <=1000USD, 100% in advance; >1000USD, 30% deposit T/T advance, 70% balance before delivery.
Q10. What is your terms of packing? A: Generally, we pack our goods in neutral brown cartons. If you have legally registered patent, we can pack the goods in your branded boxes after getting your authorization letters.
Q13. How about your delivery time? A: Generally, it will take 30 to 40 days after receiving your advance payment. The specific delivery time depends on the items and the quantity of your order.
Q14. Can you produce according to the samples? A: Yes, we can produce by your samples or technical drawings.
Q15. Do you test all your goods before delivery? A: Yes, we have 100% test before delivery
Q16: How do you make our business long-term and good relationship? A:1. We keep good quality and competitive price to ensure our customers benefit ; 2. We respect every customer as our friend and we sincerely do business and make friends with them, no matter where they come from.