All categories
Featured selections
Trade Assurance
Buyer Central
Help Center
Get the app
Become a supplier
(142 products available)
Ready to Ship
Ready to Ship
Electric snake driver
Electric snakes can be cordless or corded. Dual-ratchet-controlled cordless drivers often use lithium power.The pneumatic snake driver fits all air guns as an air pneumatic powered tools to apply motions pusher bar in small, tight spaces. The electric snake driver has spools and cutter heads that can be switched quickly and is very strong. Cordless versions can be used freely and easily, whereas corded ones are more powerful and better for longer operations.
Manual snake driver
A manual snake driver is also known as a handheld snake driver. The snake driver requires manual rotation with hands or a crank. More control, slow-speed operation minimizes the possibility of damage to the pipes. This is not as fast as electric or pneumatic ones. This driver might be less expensive, easier to handle, and good for small jobs. It is used in trap arms and small jobs, so the design is easy to be compact, portable, and affordable.
Pneumatic snake driver
The pneumatic or air-powered drivers use compressed air to rotate the augers. They are very powerful, so they are good for big jobs. The drivers are very powerful and useful for big commercial or industrial plumbing work. There is no exhaust, so they are great for areas with a lot of fumes. Be around air compressor does not portable as requires hire pressure.
Hydraulic snake driver
Hydraulic ones are only for large industrial use. They need hydraulic fluid and systems to run. The big force makes them good for thick pipes or heavy work.My very small or household plumbing problems won't need this type, just the huge industrial projects that need a lot of power.
Battery-powered snake driver
The battery snake driver is portable, easy to carry, and does not need electric outlets or air compressors. The compact design is cordless, making it easy to get in small spaces. Batts power allows use without cords or hoses. It is not as powerful as corded drivers, so it is mainly for smaller jobs like toilets or sinks.
Snake drivers are used widely because they are really helpful and durable. Here are some ways:
Auger Bit and Piston Assembly
Auger bit and piston work together to remove clogs. Clogging can be a problem for many industries if not properly managed. The auger breaks up blockages, and the piston pushes waste out.Even hard stuff like roots or grease is removed. This makes cleaning more efficient.
Commercial plumbing
This is used to maintain big plumbing systems in hotels, offices, and restaurants. They clear backups in large drains and are very strong. Their power lets them handle any size job or blockage.
Industrial facilities
Facilities use these for long-lasting drivers. They are used to maintain drains and sewers to avoid breakdowns. Regular cleaning keeps everything running smoothly and prevents expensive repairs.
Manufacturing
Factories use driveraugers to remove waste from production lines. Leducs can cause slowdowns or damage machines, so quick removal is necessary to avoid downtime. Snake drivers make this happen fast.
Mining operations
In mining, driveraugers clears sludge and debris from pipelines used to transport materials. This keeps work areas safe and ensures miners have access to clean, functioning systems.Functiioning.
Wastewater Treatment Plants
At treatment plants, snake drivers clear blockages in very large pipes. They help the big augers that install and maintain sewer lines, keeping sewage systems operational. Without them, the infrastructure would fail.
Food Processing Facilities
Food plants clear buildup and residue from processing equipment and pipelines. This prevents contamination and ensures hygiene is met. Snake drivers allow facilities to keep production high without major interruptions.
Commercial and Residential Buildings
Buildings regularly use snake-driven augers for preventative maintenance. This avoids future problems by catching clogs or buildup early. It is better to fix small issues now than deal with big headaches later.
Construction Sites
At construction sites, drivers clear runoff pipes used for dirty water and debris. This keeps work areas safe and stops flooding caused by backed-up drains. No work can happen with clogged pipes, so prompt action is critical.
Auger power cable tool
The auger is a long metal coil tool like a spring that goes down drains to clear clogs. Batts power allows it to twist and turn by itself to break up whatever is blocking the pipe. It is strong and can go down deep to clear tough clogs fast.
Flexible Shaft
The Flexible shaft driver is made of a special steel alloy that can bend without breaking. This lets it curve around bends in pipes while still being stiff enough to push debris out. It can easily wiggle through narrow spaces.Only 8-millimeter thick, it fits most drain openings. 10 meters long, it reaches deep into walls. Durable metal, won't snap. Lightweight for easy control. Bends around traps.
Twist knob
A person turns the knob at the handle to allow the auger to rotate into the drain. It smoothly spins the auger in both directions to break up clogs and remove grime. The knob is rubberized, so it is easy to grip and twist to control the auger precisely.
Retractable auger
The auger made of steel is retractable, meaning it can extend and fully contract back into the shaft after use. This allows the cable to store safely inside the housing when not in operation. It keeps the auger protected and easy to carry.
Easy clean
Flush with water, the driver easily cleans gunk off the auger after use. It prevents build-up that could cause rust. Auger is ready for next job.
Knob unlock
Begin by unlocking the twist knob at the base of the handle. It will allow the knob to retract completely. Once retracted, the auger should pull back into the housing to store safely.
Adept sliding
Once the auger retracts completely, slide the twist knob down the shaft until it reaches the handle, then twist it to lock in place. The knob safely holds the auger in place during use.
Attaching the auger
Select an auger that fits the drain size. Attach it to the end of the flexible cable by securely tightening set screws against the cable.
Put the auger in the drain
With the auger prepared, place the tip into the drain opening aligned with clog. Extend cable gently until it enters pipe a little.
Twist the knob
The auger should start spinning and digging into the clog. Keep turning knob allows auger cut through gunk build-up inside pipes. Counter-clockwise direction allows refuse to exit the drain. It takes time and patience until completely clears debris.
Clean the Projection
Clearing gunk off the drover auger is best done right after. This avoids letting muck dry and toughen hard to remove. Flush it well with water so grime washes off easily. For stuck-on dirt, a stiff brush may be needed to scrape it clean.
Check for Damage
Examining the auger for any cracks or breaks in metal parts is important. After lots of uses, the cable can wear or develop splits.Gauges in metal weaken it over time. Look closely at each part before starting work.
Lubricate Cable
Applying lubricant oil to cable every few uses helps it glide smooth. This reduces friction between cable and other moving parts, allowing it to extend and retract easily. Sliding it in and out is less likely to wear fast. Use a small amount so dirt doesn't stick to it.
Inspect Handle Mechanism
Checking the handle area is needed to ensure projection knob turns freely. Look for debris inside that jams it. Brush or compressed air removes dirt stuck in grooves. Lubricate with small amount grease so knob spins smooth.
Store Properly
Keep snake driver dry and clean-ed interior carry bag or case. Don't leave outside where weather damages metal parts. Hanging it up lets cable stay straight without kinks forming over time.
Snake drivers are one of the most important tools in a plumber's kit to clear clogs safely. It is necessary to take precautions with their care. Here are some key quality and safety points:
Durable materials
Snake driver augers are made from strong steel alloys that bend under pressure without breaking. This allows the auger to flex and maneuver through pipes of all shapes and sizes while remaining sturdy enough to break apart tough clogs deep within.Makes cleans hoods better and longer.
Flexible Shafts
The Flexible shafts are designed to easily absorb bends and curves in your plumbing. This flexibility lets the auger tip navigate around traps, bends, and other obstacles smoothly instead of snapping under stress.Fuuly cleans pipes, reaches deep, and gets closest to walls.
Handles with grips
The rubberized grips ensures a comfortable, slip-free hold even when your hands tire. This gives complete control over the auger as it rotates. The balanced weight distribution keeps it easy to maneuver with precision. Easy handling lets drivers work longer without discomfort.
Retractable auger
A retractable auger is housed safely inside the durable casing when not in use. This protects the auger from damage and keeps the driver compact for easy storage. Extended for use, it provides full operating length securely.Makes cleans hoods better and longer.
Multiple augers
Variable auger heads easily swap out depending on drain size and job requirements. Be it small trap or large sewer line, there is an ideal auger attachment available to tackle clogs of any magnitude effectively. Custom-tailored cleans powerfully mechanical hoods toward specific needs.
Inspection after use
Post-job inspections of the snake driver allow any signs of wear, tears, or damage to be spotted immediately before its performance compromised. Meticulous maintenance performed after each use guaranteed it remains safe operable for future demands.
A1: Snake drivers are used to clear clogs in plumbing pipes. They have special cable attachments called augers that can break up gunk and debris lodged in drains. Augers power cables drill through tough clogs like tree roots or grease. Snake drivers are handy for keeping pipes clean and preventing backups.
A2:The snake driver is placed into the drain opening until the auger tip enters the pipe. The handle is turned in a clockwise direction, which rotates the auger to break up the clog. As the auger powers through, the cable is pushed further to clear debris.
A3: The Snake Driver should be rinsed with water after each use to remove debris. It should be inspected for damage, lubricated with plumber's grease, and stored in a dry location. The cable may need periodic sharpening.
A4: Yes, Snake Drivers are safe when used properly. Caution should be exercised to avoid injury from the rotating auger and to avoid damaging pipes.Its usage of safety goggles during operation protects the eyes from debris.
A5: An Electric Snake Driver auger does the work automatically. People have to turn worms of manual drivers by hand, which takes longer. Electric ones are faster and easier, especially for tough clogs.
